14682.com
产品详细介绍
以下是:0.18取向硅钢卷M145-35S的产品参数
导读 0.18取向硅钢卷M145-35S_鹿程国际贸易有限公司,固定电话:13764370568,移动电话:021-56152236,联系人:鹿丙伟,QQ:871956683,宝山区蕰川公路777号宝钢厂区607-609室发货到江苏省 盐城市 亭湖区、盐都区、响水县、滨海县、阜宁县、射阳县、建湖县、东台市、大丰区 发货到 江苏省盐城市。 江苏省,盐城市 盐城市，古称盐渎，别称瓢城、登瀛、百河之城，江苏省辖地级市，长江三角洲中心区城市，位于中国东部沿海地区，江苏省东部，东临黄海，南与南通市接壤，西南与扬州市、泰州市为邻，西北与淮安市相连，北隔灌河和连云港市相望；市全境为平原地貌，为北亚热带向暖温带气候过渡地带；截至2022年底，全市辖3个区、5个县，代管1个县级市，总面积16931平方千米，常住人口668.97万人。
为了让您更地了解我们的0.18取向硅钢卷M145-35S，我们精心制作了产品视频。我们将带您领略产品的非凡之处，让您对它有更深入的了解和认识。
以下是:0.18取向硅钢卷M145-35S的图文介绍
电工钢硅钢片绝缘涂层取向电工钢产品表面均涂以一层无机绝缘涂层，该涂层具有优异的涂层特性：层间电阻高—层间电阻高，确保良好的层间绝缘性。冲片性能优—涂层与底层紧密结合，具有良好的附着性，可防止加工时涂层脱落。 叠片系数高—表面涂层均匀且薄，具有优异的叠片性能。耐热性能好—涂层能承受800℃退火，且不被损坏。耐蚀性能好—涂层与冷却油、华尔网同城绝缘油、华尔网同城机械油及氟里昂、华尔网同城防冻油等不相容，免受侵蚀。电工钢主要分为晶粒取向电工钢和晶粒无取向电工钢两大
电工钢硅钢片本文件适用于宝山钢铁股份有限公司生产的、华尔网同城用于频率在 100Hz-10000Hz 磁路结构的、华尔网同城以终退火状态交货的全工艺冷轧无取向电工钢带产品(以下简称产品)，比总损耗(铁损)specific total loss (iron loss)比总损耗是指在磁极化波形保持正弦，其峰值和频率为特定值时，单位质量材料所消耗的总功率，比总损耗用符号 P(Jm/f)表示，单位为 W/kg。例：P1.0/400表示在 磁极化强度为 1.0T、华尔网同城频率为 400Hz 时的比总损耗。Q/BQB 481－202123.2 磁极化强度 magnetic polarization磁极化强度是指试样受交变磁化时，特定磁场强度峰值的磁极化强度峰值，其符号为J(H)，单位为 T(特斯拉)。例：J5000表示对应于磁场强度峰值为 5000A/m 下的磁极化强度峰值。4 分类本文件的材料的等级是根据磁极化强度在1.0T、华尔网同城频率在400Hz下的 比总损耗值P1.0/400、华尔网同城材料公称厚度进行牌号分类，并按产品特性细分为普通型、华尔网同城型、华尔网同城高强度型、华尔网同城高磁感型和高强度型五类。示例 1：B20AV1300 表示公称厚度为 0.20mm 的普通型无取向电工钢， 比总损耗P1.0/400为13W/kg；示例 2：B27AHV1400 表示公称厚度为 0.27mm 的型无取向电工钢， 比总损耗P1.0/400为14W/kg；示例 3：B30APV1500 表示公称厚度为 0.30mm 的高磁感型无取向电工钢， 比总损耗P1.0/400为15W/kg；示例 4：B25AHV1300M表示公称厚度为0.25mm的高强度型无取向电工钢， 比总损耗P1.0/400为13W/kg；示例 5：B35AHS500 表示公称厚度为 0.35mm 的高强度型无取向电工钢，小屈服强度500MPa。1 绝缘涂层状态产品通常以两面涂敷绝缘涂层状态交货，涂层种类见表 2。绝缘涂层应可耐受绝缘漆、华尔网同城变压器油、华尔网同城机械油等介质的侵蚀。本文件规定的绝缘涂层与国内外相关技术规范规定绝缘涂层的近似对照可参见附录 A(资料性附录)，绝缘涂层的特性见附录 B(资料性附录)。绝缘涂层的厚度、华尔网同城自粘接涂层的剥离强度等技术要求如有特殊要求应在订货时协商，并在合同中注明。涂层绝缘电阻涂层绝缘电阻分为表面绝缘电阻和层间电阻，表面绝缘电阻单位为Ω·cm2/面，层间电阻单位为Ω·cm2/片，理论上，层间电阻是表面绝缘电阻的 2 倍。根据需方要求，经供需双方协商，可进行涂层绝缘电阻的检测，并在合同中注明涂层表面绝缘电阻或层间电阻的小值。
电工钢硅钢片In addition to the types listed above, there are also some special purpose electrical steel plates, such as 0.15 and 0.20mm thick 3％ Si cold-rolled non oriented silicon steel strips and 0.025, 0.05, and 0.1mm thick 3％ Si cold-rolled oriented silicon steel strips, used for medium and high-frequency motors, transformers, and pulse transformers； 0.7mm thick 3％ Si high-strength cold-rolled non oriented silicon steel plate for relays and power switches； High strength cold-rolled electrical steel plate for new high-speed motor rotors； Low carbon electrical steel hot-rolled thick and cold-rolled plates for magnetic shielding and high-energy accelerator electromagnets such as medical magnetic resonance tomography scanners； 4.5％ to 6.5％ Si high silicon steel plates for high-frequency motors, transformers, and magnetic shielding.Generally, motors, transformers, and other electrical components are required to have high efficiency, low power consumption, small size, and light weight. Electrical steel plates are usually guaranteed to have magnetic properties based on core loss and magnetic induction strength [1] [2]. The requirements for the performance of electrical steel plates are as follows:Low core loss (PT)Iron core loss refers to the ineffective electrical energy consumed by an iron core when magnetized in an alternating magnetic field of ≥ 50Hz, abbreviated as iron loss, also known as alternating loss, and its unit is W/kg. The ineffective electrical energy consumed due to various obstacles caused by magnetic flux changes not only loses electrical energy through the heating of the iron core, but also causes temperature rise of the motor and transformer. The iron loss (PT) of electrical steel includes three parts: hysteresis loss, eddy current loss (Pe), and anomalous loss (Pa). Electrical steel plates have low iron loss, which can save a lot of electricity, prolong the operating time of motors and transformers, and simplify cooling devices. Due to the iron loss of electrical steel plates, which accounts for 2.5％ to 4.5％ of the annual electricity generation in various countries, countries always try their best to reduce iron loss in the production of electrical steel plates, and use iron loss as the most important indicator to assess the magnetic properties of products. The iron loss value of products is used as the basis for classifying product grades. Cold rolled oriented electrical steel: Cold rolled oriented electrical steel is a high-end product in the field of electrical steel. Compared with cold rolled non oriented electrical steel, its magnetism has strong directionality； It has superior high magnetic permeability and low loss characteristics in the direction of easy magnetization rolling. The iron loss of oriented steel strip in the rolling direction is only 1/3 of that in the transverse direction, and the ratio of magnetic permeability is 6:1. Application: The main purpose of cold-rolled oriented silicon steel strip is for transformer manufacturing.Full process cold rolled non oriented silicon steel coating: The surface of the full process cold rolled silicon steel is coated with a semi transparent insulation coating, which has different codes in different standards. Taking Baosteel‘s Q/BQB 480 2014 as an example:
鹿程国际贸易有限公司专注生产加工 江苏盐城汽车钢, 拥有十多年生产经验。本公司是您优选的商业合作伙伴! 公司以“质量为本、客户至上、精益求精”为指导，通过人才培训，设备更新，技术革新，产业升级等一系列措施，并运用成熟的工艺、科学的管理使公司成为一家具有j i强竞争力的企业。 我们将以优的产品、真诚的服务与各界合作伙伴携手共进，共谋发展!
总结 在江苏省盐城市采买0.18取向硅钢卷M145-35S到鹿程国际贸易有限公司,无论您是个人用户还是企业采购,我们都将竭诚为您服务。品质保证,价格优惠,厂家直销,欢迎有需要的客户来电。联系人:鹿丙伟-13764370568,QQ:871956683,地址:《宝山区蕰川公路777号宝钢厂区607-609室》。